15L Equisol Xcoast Concentrate

EQUISOL XCOAT

Industrial use concentrated paint stripper and film coat remover.

Concentrated trade-strength paint stripper formula for industrial use. Removes multiple layers of old paint, failed film coatings and most solvent based finishes. Up to 3 times more coverage than other leading paint strippers. Environmentally friendly and DIY safe with no methylene chloride or NMP solvents.

WHERE TO USE:

Removes poly-urethane film, latex paints, acrylics, varnishes and stains from exterior timber, metal, masonry and brick.

CLEAN UP: Clean water and soap

SIZES AVAILABLE: 15L

COVERAGE: 10m2 per litre when diluted

Note: Equisol Xcoat is classified as Dangerous Goods.

PREPARATION:

Protect areas not to be stripped, as Equisol Strip will damage paint and other surfaces.

APPLICATION

Use only outdoors or in a well-ventilated area. Wear protective gloves and goggles. Shake bottle well. Mix ONE part Equisol Xcoat with ONE part water in a clean plastic container and stir thoroughly.

Apply to dry surface with brush, soft broom or spray in direction of the grain. Apply and strip in areas 12m2 or smaller for maximum effectiveness. Ensure Equisol Xcoat is pushed into the grain by scrubbing. Leave for 30 mins, taking care to keep timber wet with light water mist to keep Xcoat moist. After 30 mins, reapply Equisol Xcoat over the first coat and scrub in to reactivate the stripping formula. Leave on for another 30 mins.

REMOVAL: Test if finish is loose and lifts off surface with scraper. Timber will turn black where stripper is ready to be removed. Apply more stripper where timber is still light. The type and thickness of finish will affect the time until layers are loose.

Use a high pressure washer set to 50 bar (without turbo mode), working in the direction of the grain. A garden hose is not enough. Heavy finishes with multiple layers may require a repeat application of Equisol Xcoat. Once Equisol Xcoat and finish has been removed, use a garden hose to rinse off any left over chemicals on the surface. Soft timbers will feel furry due to the high pressure hose. Your timber should look bare but darker. Use Equisol Prime and Equisol Vitalise to brighten timber before oiling.

SAFETY DIRECTIONS

This substance is hazardous according to the HSNO (Minimum Degrees of Hazard) Regulations 2001.

Harmful if swallowed and in contact with skin.

Causes severe skin burns and eye damage. Toxic to aquatic life.

Avoid breathing mist, vapours or spray. Wear protective clothing, gloves, eye/face protection and suitable respirator as required. Wash hands, face and all exposed skin thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated clothing should not be allowed out of the workplace, and should be washed before re-use. Store in a closed container, in a well ventilated place and away from oxidising agents and foodstuffs. Do not empty into drains.

FIRST AID: Immediately contact a doctor or Poisons Information Centre (Phone Australia 13 11 26; New Zealand 0800 764 766). If medical advice is needed, have product container or label at hand.

IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Immediately call a POISON CENTRE or doctor/physician.

IF ON SKIN (OR HAIR): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. Wash contaminated clothing before reuse.

IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTRE or doctor/physician.

IF IN EYES: Rinse continuously with water, also under the eyelids, for at least 15 minutes. Remove contact lenses if present and easy to do – continue rinsing. Immediately call a POISON CENTRE or doctor/physician.

SPECIFIC TREATMENT: Remove from exposure and treat symptoms.

SYMPTOMS: Causes severe skin burns and eye damage. Prolonged or repeated exposure can remove natural skin oils and may produce irritation. Chronic exposure may cause liver, kidney and/or blood disorders.

NOTES TO PHYSICIAN: Treat symptomatically. May aggravate pre-existing skin disorders and pulmonary diseases.

IN CASE OF SPILL: Clear area of all unprotected personnel. Slippery when spilt. Wear protective equipment. Absorb with sand or soil. Collect and seal in properly labeled drums.

In CASE OF FIRE: Water spray (fog). Carbon dioxide (CO2). Water. Foam.

DISPOSAL: Do NOT pour leftover product down the drain. Keep unwanted product in sealed containers for disposal via chemical waste collections. Dispose of contents/containers in accordance with local regulations.

DO NOT REUSE CONTAINER. SEE THE SAFETY DATA SHEET FOR ADDITIONAL INFORMATION.

FOR EMERGENCIES call AUST 13 11 26.